Bring your engagement ring when you try on wedding bands. Two bands can look almost identical in a display tray and sit very differently beside the diamond once you put them on. The band may clear the setting, touch it at one point or leave a gap that you like.
Start with the look you want from above, then check how the two rings meet at the side and feel on your hand. If you plan to wear the band alone sometimes, try it on by itself during the same fitting.
Look for the first point of contact
In a flush fit, the bands sit beside each other with little or no visible gap. Look from the side to see what allows that fit. The wedding band may pass beneath a projecting setting or sit beside it. If the wedding band stops before the two shanks meet, find what it reaches first. It could be the basket, a side stone or another detail that extends beyond the engagement ring’s band. (Casting House)
Check two dimensions when you compare straight bands. Width describes how much space the band occupies along your finger. Thickness describes how far it rises from the finger. Two bands of the same width can have different thicknesses. The band’s upper edge and any protruding stones matter at the point where it meets the setting. A gap you like can be part of the design if the rings sit comfortably and the points of contact are appropriate.

Choose a band shape around the actual obstruction
Try a straight band first if you want an even outline for wearing alone. Check it next to the engagement ring and decide how you feel about the space between them. For a closer pairing, a broad contour can follow a basket or a curved shoulder. A notch gives one projecting detail a localized recess while keeping much of the band straight. (GOODSTONE)
| Band option | What it changes | What to check |
|---|---|---|
| Straight | Keeps an even outline | Where it stops beside the setting and how it looks alone |
| Contoured | Follows a broader curve | Clearance near the basket and shoulders |
| Notched | Makes room for a localized projection | Whether the recess stays aligned as the rings move |
| Spacer | Adds a separate band between the rings | Contact on both sides and comfort across the combined width |
If you are comparing two shaped bands, look at where each bend or cutout starts and ends. A broad curve may clear the center while touching farther out near the shoulders. A small notch needs to line up with the part it was made to clear. Turn the band to its usual wearing position, then try it alone to see how prominent that curve or notch looks.

Check what rubs before adding a spacer
Look for exposed diamond edges, small beads and prong tips along both rings. A smooth metal side resting alongside another shank presents a different contact point from an exposed diamond girdle rubbing a prong. GIA identifies neighboring diamond jewelry as a possible source of chips when stones strike hard surfaces or one another. Ask a jeweler to assess repeated contact at a stone edge or at metal that holds a stone. (GIA)
A spacer is a separate, usually slim band worn between the two rings. It can move an accent stone away from a neighboring prong if its shape and thickness create clearance at that spot. Check the spacer itself against both rings. It adds a contact surface on either side and takes up extra space on your finger. If the first spacer meets the same projecting part, ask to try another band profile. (Whiteflash)
Evaluate the pair on your finger
Put on both rings in the order you expect to wear them. Let them settle naturally, then view the top, both sides and the underside. Open and relax your hand and watch where the rings approach each other as they shift. If a contour or notch depends on the rings lining up, ask the jeweler to check the contact when either one turns a little.
Look for a change between the relaxed and bent positions. A band that sits flat beside the shank when your fingers are straight may tilt toward a prong when you bend them. If you expect to switch the order of the rings, repeat the check in both positions. Ask the jeweler to identify the surface that meets the neighboring ring on each side.
Check that the rings can pass the knuckle comfortably and feel secure together at the base of your finger. Pay attention to pressure when you make a gentle fist. GIA advises giving the combined width of a bridal set special consideration during sizing. Have the fit checked with both rings and any spacer you intend to wear. (GIA)

Compare two possible fittings
Suppose a plain straight band leaves a slim gap beside an engagement ring, and a deeper band of the same width meets the basket sooner. Ask to see both from the side. If the first band feels comfortable and keeps its edge clear as the rings shift, the gap may suit someone who also wants a straight band to wear alone. A contour is another option if a closer outline matters.
In a second hypothetical fitting, a pavé band and engagement ring look flush from above, but an exposed accent edge approaches a prong when the band turns. Ask the jeweler to locate that contact in an oblique view. Compare a band with a different side profile or a spacer that separates the two features. Recheck the new combination on the finger before choosing.
Ask for views of the selected combination
If you are shopping remotely, request a face-up photo and side view of the selected engagement ring, with the diamond option and ring size identified. Share the proposed wedding band’s width, thickness and any raised stones or edges. When a jeweler can show the actual pair, ask where they meet and how much of the gap is visible in the wearing position.
Ask where the available space is measured beside the shank, since the overall height to the top of the diamond leaves that question open. A side view of the actual pair can show what fits under the setting. Plan an in-person fitting if the photographs leave a contact point obscured or the clearance uncertain.
Frequently asked questions
Can I leave a gap between my engagement ring and wedding band?
Yes. Try the pair together and check where the rings touch when they settle or turn. A visible gap can suit your preferred look when the fit and contact work for daily wear.
Should the wedding band match the engagement ring’s width?
Try a few widths beside the actual ring. Choose the proportions you enjoy from above and check that the total width feels comfortable when you bend your finger.
Can I choose a wedding band after buying the engagement ring?
Yes. Keep the exact engagement ring available for the fitting. If you already know you want a close straight pairing, check the space beside the selected setting before buying it.
Should I size up when I add a spacer?
Try the full stack on the intended finger before changing sizes. The combined width and the inside shape of the bands can affect comfort, so have the actual combination fitted.
Browse AIMINIA lab-grown diamond engagement rings and save the option you like. Bring its side view and selected dimensions to your wedding band fitting, along with any band you already own.
Related reading
Engagement ring setting profiles · Comparing slim and wide ring bands · Ring size and fit guide.